The direct link to Bridgecom Systems for the CPS and firmware for the Anytone 878UVII+ transceiver.
D878UVII firmware update V3.03 (dated 2023-12-18)
Change List
1. Improve the scan speed, ignore some burst signal.
2. Modify the SMS to support the Text Capture on BM.
3. Modify the CPS to prohibit the CPS read the AES / ARC4 encryption from the radio, and prohibit the CPS read the AES / ARC4 encryption from the codeplug.
To avoid the mistake, we suggest you do the process as below.
1. Save the codeplug in 3.02 CPS in .rdt file.
2. Do the firmware upgrade on the radio, and after firmware upgrade, the reset is a must.
3. Run the 3.03 CPS and open the saved .rdt file, the AES keys only display xxxx now, but it still works when write the code plug into radio. To be safe, engineer suggests you re-input the AES keys in the
CPS before loading to radio, then it must work.
4. CPS->Optional setting->Key function, add the “dim shut” function which allow set a key to shut off the
radio backlight and LED completely.
5. Modify the firmware to make the AES encryption have a variable Vector(IV) instead of fixed “12345678”.
Firmware version: V3.03
CPS version: V3.03
SCT 3258 version: V2.01.07 BA （same, no need update）
BT Version: 10036 or 10043 or 19043 (no need update)
APRS ver: 1.06 or 2.00 (no need update)
AnyTone 878 (V2 Model) CPS & Firmware
Warning: Firmware uploads are done at your own risk, and damage from attempting this procedure is not guaranteed to be covered under warranty. Update instructions are included in the CPS download folder, and we strongly recommend reading through it before attempting this procedure. To prevent unexpected results, a factory reset of the radio must be performed after uploading the new firmware, and the CPS version used to write the radio must match the firmware version that is installed on the radio.
D878UVII firmware update V3.03 (dated 2023-12-18)
Change List
1. Improve the scan speed, ignore some burst signal.
2. Modify the SMS to support the Text Capture on BM.
3. Modify the CPS to prohibit the CPS read the AES / ARC4 encryption from the radio, and prohibit the CPS read the AES / ARC4 encryption from the codeplug.
To avoid the mistake, we suggest you do the process as below.
1. Save the codeplug in 3.02 CPS in .rdt file.
2. Do the firmware upgrade on the radio, and after firmware upgrade, the reset is a must.
3. Run the 3.03 CPS and open the saved .rdt file, the AES keys only display xxxx now, but it still works when write the code plug into radio. To be safe, engineer suggests you re-input the AES keys in the
CPS before loading to radio, then it must work.
4. CPS->Optional setting->Key function, add the “dim shut” function which allow set a key to shut off the
radio backlight and LED completely.
5. Modify the firmware to make the AES encryption have a variable Vector(IV) instead of fixed “12345678”.
Firmware version: V3.03
CPS version: V3.03
SCT 3258 version: V2.01.07 BA （same, no need update）
BT Version: 10036 or 10043 or 19043 (no need update)
APRS ver: 1.06 or 2.00 (no need update)
AnyTone 878 (V2 Model) CPS & Firmware
Warning: Firmware uploads are done at your own risk, and damage from attempting this procedure is not guaranteed to be covered under warranty. Update instructions are included in the CPS download folder, and we strongly recommend reading through it before attempting this procedure. To prevent unexpected results, a factory reset of the radio must be performed after uploading the new firmware, and the CPS version used to write the radio must match the firmware version that is installed on the radio.
Last edited: